All Swim PAK 3 Calcium Chloride Hardness Plus (Raises Calcium Hardness)

Calcium Chloride - Raises Calcium Hardness
Availability: In stock

£15.00

*

Free UK Delivery Over £60
UK Mainland Only (Excludes Highlands)
Excludes Hot Tubs & Swimspas except Inflatables

All Prices include VAT

Calcium hardness is the measurement of dissolved calcium in the water. For swimming pools, calcium hardness should be maintained at a minimum of 200 mg/l (ppm). Low levels can harm the pool and its equipment. Test the calcium hardness level of the pool water and if it is below 200 mg/l (ppm) use All Swim Pak 3 to increase the level.

Application Instructions

  1. Pre-dissolve the product in a clean plastic container at a maximum rate of 100g of product per 2.2 gallons (10lts) of clean cold water. Stir well to ensure product is fully dissolved.  Carefully add the resulting solution to the pool whilst the pump(s) are turned "on", preferably near to the water inlets to aid distribution.
  2. The total amount of Calcium Hardness Raiser required can be calculated using the dosing table below. This total should be split into 3 doses with a minimum of 6 - 8 hours left between each subsequent dose.

Water Volumes Dose Rates
Litres Gallons To Increase Calcium Hardness By 10mg/l(ppm) To Increase Calcium Hardness By 25mg/l(ppm)
4,545 1,000 68g 170g
9,090 2,000 136g 340g
22,700 5,000 340g 840g
45,450 10,000 680g 1.70kg
68,175 15,000 1.02kg 2.55kg

 

General Precautions

Dosing

  • Wear eye and face protection and ensure granules are not blown back into your face.
  • Never mix with other chemicals including household cleaners as a dangerous reaction may occur.
  • When pre-dissolving always add product to water and not vice versa.

Handling/Storage

  • Handle products in a well ventilated area - preferably outdoors.
  • Wash hands after use.
  • Ensure chemicals do not become damp in storage - store in a cool dry place.

Calcium hardness is the measurement of dissolved calcium in the water. For swimming pools, calcium hardness should be maintained at a minimum of 200 mg/l (ppm). Low levels can harm the pool and its equipment. Test the calcium hardness level of the pool water and if it is below 200 mg/l (ppm) use All Swim Pak 3 to increase the level.

Application Instructions

  1. Pre-dissolve the product in a clean plastic container at a maximum rate of 100g of product per 2.2 gallons (10lts) of clean cold water. Stir well to ensure product is fully dissolved.  Carefully add the resulting solution to the pool whilst the pump(s) are turned "on", preferably near to the water inlets to aid distribution.
  2. The total amount of Calcium Hardness Raiser required can be calculated using the dosing table below. This total should be split into 3 doses with a minimum of 6 - 8 hours left between each subsequent dose.

Water Volumes Dose Rates
Litres Gallons To Increase Calcium Hardness By 10mg/l(ppm) To Increase Calcium Hardness By 25mg/l(ppm)
4,545 1,000 68g 170g
9,090 2,000 136g 340g
22,700 5,000 340g 840g
45,450 10,000 680g 1.70kg
68,175 15,000 1.02kg 2.55kg

 

General Precautions

Dosing

  • Wear eye and face protection and ensure granules are not blown back into your face.
  • Never mix with other chemicals including household cleaners as a dangerous reaction may occur.
  • When pre-dissolving always add product to water and not vice versa.

Handling/Storage

  • Handle products in a well ventilated area - preferably outdoors.
  • Wash hands after use.
  • Ensure chemicals do not become damp in storage - store in a cool dry place.



2024 All Swim Catalogue
A.J & J.L Veysey | Company registration no: 1061642 | VAT no: GB133 4078 90
All Swim Ltd, Units 3-5 Link Trade Park, Penarth Road, Cardiff CF11 8TQ